Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Liner & Rebuild Cost in Arleta?
In Arleta, a stainless-steel liner installation typically runs $1,900 to $4,800, and a partial chimney rebuild usually lands between $2,800 and $9,500, depending on how much brick and flue work is involved. A full rebuild from the roofline up can climb past $12,000 when the crown, flashing and flue interior all need replacing at once. These are estimated ranges, and the written estimate you get after an inspection sets the final price.
Most Arleta homes were built in the postwar decades, and the chimneys that came with them were lined with clay tile. Clay cracks. When it does, the flue gases have a path into the framing. That’s the single biggest reason liner and rebuild work comes up in this part of the San Fernando Valley, and it’s why we put a camera down the flue before quoting anything.
Key Takeaways
- Liner replacement: typically $1,900 to $4,800, with length and diameter driving most of the spread.
- Partial rebuild (upper stack, crown, flashing): roughly $2,800 to $9,500.
- Full rebuild above the roofline: can run $12,000 and up on a two-story home.
- HeatShield resurfacing is often the middle path when the flue is rough but structurally sound.
- Estimates are free. Call (833) 958-9616. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Chimney Liner & Rebuild Cost Breakdown (2026)
Here’s how the work breaks down line by line for the Arleta market. These are typical figures for a single-flue masonry chimney on a one- or two-story house. Prefab and factory-built units price differently, and gas insert flues usually sit at the low end because the liner run is shorter.
| Line item | Typical estimated range | What it covers |
|---|---|---|
| DuraFlex stainless liner, 6″ for wood | $1,900 – $3,900 | UL-listed flexible stainless liner, insulation wrap, top plate, cap |
| Larger-diameter liner (8″ or oversized flue) | $2,600 – $4,800 | More stainless per foot and a bigger footprint to fit |
| HeatShield flue resurfacing | $1,400 – $3,200 | Ceramic-based resurfacing of a deteriorating but intact clay flue |
| Crown repair or replacement | $600 – $1,800 | The concrete cap at the top that sheds water off the stack |
| Flashing repair or replacement | $500 – $1,600 | Sealing the roof-to-chimney joint against rain |
| Partial rebuild (upper stack) | $2,800 – $6,500 | Rebuilding brick from the roofline up, new crown and flue tile |
| Full rebuild above the roofline | $6,500 – $12,000+ | Full brick stack rebuild, new flue, crown, flashing, cap |
| Damper or cap replacement | $350 – $900 | Top-sealing damper, stainless cap, or both |
What pushes a job toward the top of a range? Length of the flue run, how much brick is spalled or crumbling, whether scaffolding is needed, and whether the original clay tiles have to come out before a new liner goes in. Removing broken tile is slow work, and it’s often the difference between a mid-range liner quote and a high one. The inverse is also true: a short flue with sound tile and a decent crown can be lined for less than the low end of the range above.
Every one of these jobs is priced per job, by written estimate. We don’t quote over the phone from a photo and we don’t pad a liner quote with work the flue doesn’t need.
What Affects Chimney Liner & Rebuild Pricing in Arleta
Cost here isn’t random. A handful of things move the number, and most of them come back to how the house was built.
- Postwar clay tile construction. A lot of Arleta housing stock went up in the 1940s through the 1960s, when clay-tile flues were standard. Tile that’s been through six or seven decades of heating cycles is often cracked or has separated at the joints. That means a new stainless liner isn’t an upgrade, it’s a repair, and the price reflects removing or bypassing failed tile.
- Flue length and roofline height. A one-story flue might run twelve feet. A two-story home with a steep roof pitch could run thirty. Stainless liner is sold by the foot, so the run length shows up directly on the estimate. A roof that needs scaffolding or a longer ladder adds labor.
- Masonry condition at the top. The stack above the roofline takes the most weather. Spalled brick, a cracked crown and tired flashing are the three things we look at first. Fixing them during a liner job costs less than coming back for them later, and a water-damaged stack is the main reason a liner job turns into a rebuild.
- Liner material and brand. We install DuraFlex liner systems, not generic stainless from a home center bin. The wall thickness, the alloy and the UL listing all matter, and the professional-grade product costs more than the budget roll. We also source Gelco and Olympia Chimney components, so the buyer can look up exactly what’s going into the flue. That transparency is worth something.
- HeatShield versus full relining. When the flue interior is rough but still sound, HeatShield resurfacing can restore it at a lower cost than a full stainless liner. We check which path fits before we quote, because not every chimney needs a liner and not every rough flue can be saved with resurfacing.
- Whether the chimney is masonry or prefab. Factory-built fireplaces use their own listed venting. Famco venting components come into play on those systems, and replacing a prefab vent section prices differently from a masonry liner. It’s a shorter, more standardized job in most cases.
One more local note: our wet winters in the Valley don’t freeze the masonry, but they do soak it. A chimney with a failed crown takes on water all winter, and that water is what eventually spalls the brick and cracks the flue tile. Addressing the crown during a liner job is usually the cheapest line on the whole estimate, and it protects everything above it.
How to Save on Chimney Liner & Rebuild
There’s no honest way to make a chimney rebuild cheap, but there are real ways to keep the number from climbing.
- Get the flue inspected before small problems grow. A cracked crown repaired for a few hundred dollars is a very different bill from a partial rebuild years later. Early diagnosis is the biggest cost saver in this trade.
- Bundle the liner with the crown and flashing. If the stack is coming apart for a reline anyway, fixing the crown and flashing in the same visit avoids paying twice for the same access. We price the whole job in one written estimate so you can see that.
- Ask whether HeatShield fits your flue. Resurfacing the interior is often the lower-cost route when the tile is rough but intact. We’ll tell you honestly if it doesn’t apply.
- Skip the low bid from a sweep with no repair scope. A sweep who only cleans will note the crack on an inspection sheet and hand you a referral. Then you pay for a second company to come back. One provider for inspection, cleaning and structural repair is the cheaper path in the end.
- Take the free estimate seriously. We’ll put a camera down the flue and give you a written scope with line items, so you can compare apples to apples with any other quote. Call (833) 958-9616 for a free estimate.
One thing worth saying plainly: high-temperature silicone liner is not a place to save. It sits behind the fire. Cutting corners there is the one shortcut that can cost you the house.
FAQs – Chimney Liner & Rebuild Cost
How much does a chimney liner cost in Arleta in 2026?
A chimney liner in Arleta typically costs $1,900 to $4,800 installed. The low end covers a short 6″ stainless run for a wood fireplace; the high end covers an oversized flue, longer run, or a job that requires removing broken clay tile first. Call (833) 958-9616 for an exact quote. Estimates are free.
Is it cheaper to repair a chimney or rebuild it?
Repair is almost always cheaper: resurfacing or a partial crown fix usually runs $1,400 to $3,200, against $2,800 and up for a partial rebuild. Rebuild only makes sense when the brick above the roofline is spalled or the flue structure is gone. Call (833) 958-9616 and we’ll tell you which one your chimney actually needs.
How much does a chimney rebuild cost in Arleta?
A partial rebuild in Arleta typically runs $2,800 to $6,500, and a full rebuild above the roofline can hit $6,500 to $12,000 or more on a two-story home. Height, brick condition and whether the flue tile needs replacing set the final number. Call (833) 958-9616. Estimates are free.
Can you install a liner the same day?
Yes, a straightforward liner installation is usually a same-day job once the flue is inspected and the liner is on hand. Jobs that need broken tile removed first, or that turn into a rebuild, take longer. Call (833) 958-9616 to book an inspection. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Do I need a permit for a chimney liner or rebuild in Arleta?
Most cities require a permit for structural chimney work like a rebuild, so it pays to check with the local building department before work starts. Many liner installations can be done without structural permits, but the rules vary. We’ll walk you through what applies to your job. Call (833) 958-9616.
Why do you use DuraFlex and HeatShield instead of generic parts?
Because the product is safety equipment, not trim. DuraFlex is UL-listed flexible stainless built for masonry and prefab flues, and HeatShield is a recognized resurfacing system for deteriorating flue interiors. Professional supply-house brands come with listed materials and traceable specs that let you verify what went in. Call (833) 958-9616 to talk through the right system for your chimney.
Let’s Get a Real Number for Your Chimney
Here’s what we’re installing and why, and here’s what it costs, on paper, before anyone starts. We clean it, and if it needs repair, we fix it, all under one roof, with professional-grade materials named on the estimate. If you’ve got a flue that needs lining, a stack that’s crumbling at the top, or just a bad feeling about the chimney heading into this winter, call (833) 958-9616. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Want to know more about who’s doing the work? Chimney Sweep Arleta covers our full service scope, and our Arleta service page shows how we handle the local housing stock. Dryer vent cleaning is available too. It’s a fire risk a lot of homeowners never think about, and one call covers your chimney and your dryer vent.
Pricing reflects the Arleta market as of 2026. Chimney Sweep Arleta offers free estimates – call (833) 958-9616.
Written by the team at Chimney Sweep Arleta, serving Arleta since 2017.
What Our Customers Say
"Cap keeps the birds out now, which after two springs of scratching noises is worth every penny."
- Angela Wong"Creosote buildup was worse than I realized. He measured it, showed me the glazing on the flue with the camera, and was honest that we were closer to a chimney fire than I wanted to hear."
- Andres Vargas"We manage six rental properties and I've now sent them to four of them. Consistent every single time, which is not something I can say about most vendors we use."
- Henry Tran